Nobilia filler strips, fillers & angled fillers

Nobilia filler strips and fillers close gaps between wall and cabinet, compensate for uneven walls, and connect cabinets neatly around corners. They are available in front or carcass material and match base cabinets, highboards, tall cabinets, wall cabinets, top cabinets, and bridge cabinets exactly in height, width, and depth – for a calm, continuous line.

Advantages at a glance:

• Compensation for uneven walls & harmonious front appearance

• Perfect corner solutions for L-shaped kitchens thanks to angled fillers

• Suitable for all Nobilia cabinet heights (72 – 216.6 cm)

Nobilia fillers for base cabinets provide clean wall finishes, precise corner solutions, and a continuous front line in every kitchen run. Whether filler strips in carcass material, front fillers, or angled fillers such as UPE and UPE-V – they precisely compensate for widths, wall tolerances, and corners. Ideal for L-shaped kitchens and flush planning with base cabinets in 72 cm, 79.2 cm, and 86.4 cm.

Nobilia filler pieces for highboards enable clean wall and corner finishes on tall cabinets and ensure that front lines continue without offsets. With filler strips in carcass material (HPK20) or front filler pieces (HPD20), as well as angled filler pieces such as HPE and HPE-V, widths, wall tolerances, and corners can be perfectly compensated for – matching highboard heights of 151.2 cm and 158.4 cm.

Nobilia filler pieces for tall cabinets precisely close side gaps and ensure a flush, calm front line for all tall cabinet heights. They are available to match 201.6 cm, 208.8 cm, 216.6 cm, and 233.2 cm – for both standard and XL heights. With filler strips (HPK20-1), front filler pieces (HPD20-1), and angled filler pieces such as HPE-1 or HPE-V-1, wall connections and corners can be adjusted exactly.

Nobilia filler pieces for wall cabinets create clean wall finishes, harmonious lines, and fit all common wall cabinet heights – 36 cm, 57.6 cm, 72 cm, 79.2 cm, and 86.4 cm. With carcass filler strips (WPK10-1), front filler pieces (WPD20-1), and angled filler pieces such as WPE45-58, widths, heights, and corners can be precisely adapted to uneven walls or niches.

Front filler pieces for wall cabinets are constructed in a C-shape. They have a top panel above and a bottom panel below so that the gap is completely closed. This prevents dust from falling into the niche, and there is no visible opening from below – ideal for visible run-end finishes and a premium kitchen look. With standard front filler pieces, the gap is concealed from the front – the top and bottom remain open and uncovered.

Nobilia filler pieces for top cabinets enable flush finishes between the top cabinet and wall or tall cabinet and ensure a clean, continuous front line. Matching top cabinet heights of 75.4 cm, 104.2 cm, 125.8 cm, and 133 cm, there are carcass-colored filler strips such as APK20-75 as well as front-material-matched front filler pieces such as APD20-3, ideal for visible areas and harmonious transitions.

Nobilia filler pieces for bridging cabinets ensure clean finishes above freestanding refrigerators or appliance housings and precisely compensate for side niches. Matching the common bridging cabinet heights of 19.4 cm, 36 cm, and 72 cm, carcass-colored filler strips such as UFKPK20-72 as well as front-material-matched front filler pieces such as UFKPD20-36 are available – ideal for harmonious, flush refrigerator housings.

Nobilia filler strips, filler pieces, and angled filler pieces are precise compensation elements that close gaps between wall and cabinet, connect corners, and compensate for height, depth, and width tolerances. Since walls are rarely perfectly plumb, they prevent visible joints, creeping gaps, and uneven transitions. The result: a kitchen run that looks clean, flush, and like one continuous piece of furniture.

Front filler pieces are suitable for all visible areas where the front line should continue seamlessly – exactly in the front color and with a premium look. Carcass filler pieces are the subtle, budget-friendly alternative for side wall connections in the carcass decor. They close gaps functionally, discreetly, and with a precise fit.

You use front filler pieces wherever the finish is visible and the front line should continue seamlessly. They are made from the same material as Nobilia kitchen fronts, are 19 mm thick, and are available exactly in your front color. The integrated rubber lip compensates for small wall unevenness and ensures a clean finish.

The standard width is 20 cm. If desired, you can also order front filler pieces as custom-made center filler pieces. These have a small attached side panel on the left and right, allowing you to screw the filler piece securely and precisely between two cabinets – ideal for closing central gaps with a premium finish.

Typical front decors include:

• Melamine & lacquer laminate programs: 427 Alpine white | 336 lacquer laminate, Magnolia super matte | 488 lacquer, white premium matte

• Lacquer & framed fronts: 467 lacquer, sand ultra high gloss | 516 lacquer, Alpine white high gloss | 847 lacquer, Alpine white matte

• Further programs: 605 Coffee textured | 966 lacquer laminate, fjord blue ultra matte | 390 Magnolia brushed

Thanks to this wide selection, you can order every filler piece in the front color – perfect for high-quality, continuous front lines without a style break.

Carcass filler pieces are the simple and budget-friendly solution for side wall connections. They are made from the same material as the Nobilia carcass, are 16 mm thick, and are available in all carcass colors. The 10 cm and 20 cm widths are trimmed on site to the required size. They are mounted slightly set back and flush with the carcass, not with the front – perfect for subtle, discreet finishes in less visible areas.

Typical carcass decors include:

• Solid and gray shades: 193 Alpine white, 106 white, 070 silk gray, 089 stone gray, 194 slate gray, 127 black

• Wood decors: 078 oak San Remo reproduction, 198 oak Sierra reproduction, 097 oak Havana reproduction

• Further shades: 120 Magnolia matte, 122 sand, 060 Alpine white gloss (discontinued)

This allows simple light kitchens, warm wood looks, and modern dark plans to be finished coherently and neatly.

The planning dimension describes the unused footprint of the corner – the so-called dead corner. A regular UPE angled filler piece is always used when the adjacent cabinets are positioned so that a non-usable area of 65 × 65 cm is created behind the filler piece. This area remains empty and cannot be used for storage. Drawers and front pull-outs next to the corner remain fully functional through the use of the corner filler piece.

If your room situation differs from this planning dimension, you use a variable angled filler piece. This covers planning dimensions from 63 to 75 cm. For this, you specify the left and right dimensions separately so that the filler piece is matched exactly to your individual kitchen plan.

Note: An increase in the planning dimension leads to an increase in the leg dimension in the same proportion. With a planning dimension of 65 x 65 cm, the leg dimension is 7 cm.

The corner dimension of 650 x 650 mm enables plans with drawers or front pull-outs next to the corner; there are no obstructions caused by protruding handles. Please take the respective handle height into account in your planning.

You use a 90° angled filler piece in classic L-shaped kitchens when two runs meet at a right angle and the corner should remain compact. This solution creates a “dead corner,” offers no storage space, but is the most cost-effective entry-level option and ensures collision-free door and pull-out movements. A 135° angled filler piece is used when the corner should appear more open, chamfered, or ergonomic – ideal for modern, flowing kitchens and spacious walkways. It requires more space but creates a more harmonious corner design.

You use a 90° angled filler piece when your kitchen is classically planned as an L-shaped kitchen with a right angle. Two runs meet at a 90° angle, the cabinets stand parallel to the walls, and the corner should remain compact. This is the standard solution in most kitchens because it requires little space and the footprint and planning dimensions are clearly defined. With variable angled filler pieces, dimension 1 describes the left planning dimension and dimension 2 the right. This allows the two run lengths of an L-shaped kitchen to be adjusted precisely.

A 135° angled filler piece is used when the corner should appear chamfered or more open – for example in open-plan kitchens, spacious walkways, or when the kitchen should look less “boxy.” The 135° angle brings the corner ergonomically forward, makes it appear softer, and requires more space.